You don’t know how to vent your kitchen sink through a window? This article will provide a step-by-step guide. These are the six steps: Measure the vent pipe, cut it, draw a line and drill a hole. Once the pipe is positioned, attach it to the wall.Also visit a carpenter near me.
How do you vent a kitchen sink from under a window?
You get assured of an easy process if you follow the guidelines for venting a kitchen sink for a window. But first, you will need to have the doing steps:
Step 1: Measure the brick thickness and distance.
Measure the brick thickness and distance from the brick end to make a hole in your wall. Then, measure brick length and re-measure it as needed for dispatching. You should also measure the wall’s thickness at each height.
Step 2: Make sure you measure accurately.
With a sharp knife, cut a 2-inch length from 1 1/2-inch PVC pipe in the kitchen and bend it to make a section. It should be inserted through the holes. Then glue it to your elbow. Attach a second elbow to one side of the pipe, with the outlet facing up.
Sand the line. Install a 2″ PVC elbow to replace the backup valve. It should be wired to a 2-inch threaded adapter and a 3-/8 “-1/2” threaded access fitting. This will be added to your system in the future, so make sure it’s as good as new until that time.
Two 6” long pieces of 1/ 2-inch PVC should be cut. One piece of 1/2’s PVC should be cut to 2 inches, and the other one to 6 inches. A 2-inch length 1 1/2-inch HTMLVC pipe is cut. Use a sharp knife to cut a 2-inch section of 1 1/2 inch PVC pipe .
Ns insert it through the holes, and glue it to your elbow. Attach a second elbow to one side of the pipe, with the outlet facing up. Sand the line. Install a PVC elbow 2” in diameter, wired to a 2″ threaded hose adapter with a 3/8″-1/2″ threaded access fitting.
Step 3: Draw an imaginary line underneath the window.
You can draw a line along the wall and measure the length of your drain from the point just beyond the window. Draw a line with chalk to the point where the pipe can be turned upward.
To determine the vertical position of a horizontal line, use the line height. These guidelines will assist you in achieving it.
The line should point straight down towards the window if it is not. If a line is to be drawn 25 feet from a point five feet away from the window it should be closer than 10ft, 1ft, or 2ft.
Step 4: Drilling a hole measuring one- and a half inches.
A small hole will be made at the PVC pipe’s end where it meets the wall. You can use electrical tape to straighten the plumbing pipes or rubber grommets to fix them.
Make a hole of one-and-a-half inches in the top plate of the wall. The Vent will be extended into the attic. It can be routed horizontally to connect with the main vent stack.
Next, drill a hole in the plate. The Vent is paralleled by a 2 1/4-inch length of metal pipe. A 5/8-inch piece of metal pipe is perpendicular. The gutter cover will be held by the two 1/4-inch lengths of metal pipe.Also visit handyman dubai.
To provide additional airflow, the exhaust fan inlet is mounted on a single 5/8 inch metal pipe. The gutter cover is connected to the exhaust fan via a 3/4-inch plastic tube. You may not have a vent stack in your attic so you will need one.
Step 5: Install the vent pipe
Use a screwdriver to install a vent pipe into the wall. Next, you will need to drill the hole. You should have a line that is about 2 inches wide on each side. Use PVC cement to glue it to the 1 1/2-inch port of the sanitary tee.
Next, take the sweep elbow. Place it on the pipe. After this, remove the top flange. Now you should have two pieces of pipe that are squared together.
Step 6: Connecting the pipe to the hole
You will need a drill or a screwdriver to insert the vent pipe into the opening in the wall. Tape will be used to attach the vent pipe to your wall.
To see the Vent through it, position the vent pipe. To view your attic, it should be placed near the wall. Your vent pipe should be oriented towards your center. This will allow you to see more of your home and reduce noise levels.
